The Non-Destruction Inspection Technician (NDI) III inspects aerospace weapon systems components and support equipment for structural integrity using nondestructive inspection methods and performs fluid analysis.

• Conduct the training and examination on all NDT methods to certify and to re- certify all operators and inspectors as outlined in NAS 410 or ASNT-CP-189.

• Determine test method and prepare fluids and parts for nondestructive inspection.

• Interpret nondestructive inspection test results and provide information about defects to repair center.

• Analyze wear metal content reports on engine lubricating oil and other fluids and recommend corrective action.

• Establish radiation areas for radiographic operations.

• Compute and monitor personal exposure areas for radiographic operations, and monitor personnel exposure data.

• Perform nondestructive inspection on structures, components, and systems.

• Detect flaws such as cracks, delamination’s, voids, processing defects, and heat damage using penetrant, eddy current, magnetic particle, radiographic, optical, and ultrasonic test equipment.

• Determine metallurgical information of components according to alloy, temper, conductivity, and associated factors.

• Operate, maintain, and inspect nondestructive equipment.

• Perform operator maintenance and service inspections on shop equipment and tools.

• Ensure lock out and tag out procedures are accomplished prior to maintenance on equipment.

• Perform silver recovery functions.

• Handle and dispose of hazardous waste and materials

• Perform other qualified duties as assigned.

Minimum Requirements:

• Completion of high school or equivalent and U.S. military technical school or specialized training course is desired, certification of education level is required.

• Trained and certified as an Examiner (Level III) to monitor the NDT Program, interpret codes, standards and other contractual documents that control the NDT method, will be certified to review their own x-rays.

• Three (3) years’ experience as a Non Destructive Inspection (NDI).

• A Valid US Passport is Required for deployment to Kuwait. The Passport must have 3 years remaining before expiring, and 6 Blank pages available at the time of hire and deployment.

• Must be able to pass and clear CENTCOM Army MOD Physical and requirements for deployment (will attend CRC/ DIDC Training).

• Must be able to obtain Kuwait PCC clearance and Visa, prior to deployment.

Security Clearance Requirements:

• Must be able to obtain and maintain a US Govt NAC-I (T1) Public Trust Security Clearance. Must be able to obtain and maintain facility credentials/authorization. US Citizenship is required to obtain a Clearance and for facility credentials/authorization to work at this facility.

Additional and Preferred Qualifications:

• Have the skills and knowledge to interpret codes, standards, and other contractual documents that control the approved NDT method(s).

• Capable of assuming technical responsibility for the NDT facility and staff.

• Capable of selecting the method and technique for a specific inspection.

• Capable of preparing and verifying the adequacy of procedures in the method certified.

• Approve NDT procedures and other NDT related work instructions for technical adequacy in the method in which they are certified.

• Capable of providing or directing training, examination, and certification of personnel in the method in which they are certified.

• Thoroughly familiar with the scope and limitations of the technique/method in which they are certified.

• Capable of providing the necessary guidance and supervision to trainers and personnel in the technique/method in which they are certified.

• Knowledge of electrical, mechanical, electronic, hydraulic and pneumatic systems or other technology as applicable to fabrication, repair, operation and maintenance requirements.

• Efficient in record keeping and preparation of reports; capable of reviewing other people's work and determining accuracy and conformity to standards.

• Proficient in the use of the Unit Level Logistics System-Aviation Enhanced (ULLS-AE), the current maintenance management system utilized to maintain Army aircraft forms and records.

• Thorough comprehensive knowledge of aircraft mechanical component troubleshooting/repair procedures and replacement of components.

• Thorough knowledge of aircraft sheet metal/structural modification and repair and the ability to determine functionality of non-complex electrical systems.

• Detailed knowledge of aircraft unique tools such as test equipment, torque wrenches, dial indicators, micrometers, cable tensiometers, sheet metal brakes and sheers, etc. preferred.

• Ability to provide technical support to structural/mechanical engineers and customers.

• Excellent organizational skills in prioritizing workload to meet aircraft delivery schedule.

Physical Requirements/Working Environment

• Must be able to walk and stand on level and/or inclined surfaces for extended periods throughout the day

• Must be able to climb stairs, ramps, ladders, and work stands

• Must be able to crouch, crawl, grasp or handle objects, use finger dexterity, bend elbow/knee and reach above/below shoulders

• May be required to lift heavy objects whose weight may exceed 50 pounds

• Must be able to type using a standard keyboard to communicate through e-mail and various software applications

• Will handle dirty parts and lubricants

• Will be required to wear proper Personal Protective Equipment (PPE)

• Must be able to pass a Respirator Physical and Fit Test qualification

• May be required to operate power vehicles, machinery, hand tools, ground support equipment, fork lift, etc.

• Must be able to lift/push/pull minimum of 50 pounds

• May work in maintenance shop or outside

• Must be able to work in a shop where the environment is drafty, noisy, and dirty

• May be exposed to extreme noise from operating equipment

• May be exposed to electrical shock hazards or work near moving mechanical parts or vehicles.